На главнуюТранспортПохожее видеоЕще от: proclaimliberty2000

(Part 4) How To Fix Your Check Engine, VSC, Trac Off Warning Lights On With Zero Point Calibration

Оценок: 4208 | Просмотров: 437168
Anyone can do a Zero Point Calibration. It will also be neccessary to perform after installing bigger tires, lift kits and after performing a front-end wheel alignment.
Категория: Транспорт
Html code for embedding videos on your blog
Текстовые комментарии (194)
Oleg Kot (6 дней назад)
thank you, your video helped me to fix this issue
Ben Hill (8 дней назад)
Awesome video, thanks so much!!! Worked immediately and saved me big $$$ at the dealership!
Daniel Morvec (13 дней назад)
This worked for me. 2005 Sienna. 1 thru 3 did nothing. Step 4 was the cure. Thanks.
proclaimliberty2000 (13 дней назад)
Daniel Morvec 👍
bobby redondo (24 дня назад)
the gas cap thing worked for me thanks
proclaimliberty2000 (24 дня назад)
bobby redondo 👍
bobby redondo (24 дня назад)
you are a boss
bobby redondo (24 дня назад)
get some glasses and you and Scotty Kilmer would be mates
Pip (25 дней назад)
.... and do the Hokey Pokey and turn yourself around.
Gerardo Moreno Chinchilla (1 месяц назад)
Thanks a lot. It worked and I´ve repaired my Electronic Power Steering with your help, my RAV4 2006 had the problem that the EPS was working not correctly, very hard and the car was very difficult keep straight on the highways. The Toyota Dealer asked me to change all system, costing arround 2000€, imagine... thank you Paul
proclaimliberty2000 (1 месяц назад)
Gerardo Moreno Chinchilla You’re welcome.
Michael Clark (1 месяц назад)
It worked thank you!
Raji Morufu (1 месяц назад)
PLEASE HELP* which terminals do I use on a 2004 lexuz rx 330???
Robert Nguyen (1 месяц назад)
very good, attention to detail, very clear step by step. Thanks
Tyrees Taylor (2 месяца назад)
I have a 2002 Lexus LS 430 ultra. Does this work the same for every car?
Joe Minoso (2 месяца назад)
Solved the problem part 3...sienna 2002...thank you
proclaimliberty2000 (2 месяца назад)
Joe Minoso You’re very welcome Joe!
Bobby8451 (2 месяца назад)
I'm was just waiting on a big spark using those paper clips. Lol
Thang Tons (2 месяца назад)
Sir following the same procedure can we activate auto door lock in Hyundai i20 with joining the pins in corresponding pins? Thanks.
Khoa Le (2 месяца назад)
The first step of tapping the 2 paper clips didn't work. However, holding it together worked. Better yet just have 1 paper clip into the pins worked for me. Used on Toyota Sienna 2009.
Tony Eze (2 месяца назад)
Great video! Does it work if the ABS is on with the VSC as well?
proclaimliberty2000 (2 месяца назад)
It probably will but there is no guarantee but it can save you a ton of money. Let me know what happens.
MidniteClubII (2 месяца назад)
RIGHT ON! Very helpful
wayne mazan (2 месяца назад)
Great video thanks !!!!
abby albert (2 месяца назад)
very nice vdo sir
Pd Mahesh Sharma (3 месяца назад)
THANK YOU BROTHER FOR YOUR TIME TO EXPLANE
proclaimliberty2000 (3 месяца назад)
Pd Mahesh Sharma You’re very welcome!
Jackey Cho (3 месяца назад)
part 4 is way over head
Beez Benny Blanco (3 месяца назад)
Super !!! A+!!! HAD VSC AND TCS light on a 2003 TOYOTA CAMRY XLE V6, MADE SURE I CONNECTED THRU PIN 4 & 14, DID THE SAME PROCEDURE AND WORKED PERFECT!
Sensei Sensei (3 месяца назад)
My alphard 2003 vsc,trc and check engine light come out after i holding brake pedal for 10 sec after D transmission.. thanx sir
Sensei Sensei (3 месяца назад)
Hello sir.. my car alphard 2003.. can u help me? I dont know where to find the ts and cg port on my obd..
Arfan Ali (3 месяца назад)
Im Pakistan
Mikael Sjödin (3 месяца назад)
proclaimliberty2000. Okey i will do that, thank's for your help, if it is not to big problem then i can buy the part and then do the job myself. Have a great day and summer.
Mikael Sjödin (3 месяца назад)
I have a problem that the VSC and TRAC OFF came on and the engine lost their power but i was able to drive home, i found this and made it today and in the beginning it worked but after a while the lights came on again and the power in the engine dissapeared again, so it didn't work for me so it must be something else that is wrong, somebody got a suggestion what it might be?, i have checked all the fuses for brakes and light bulbs and they are all okey, i also checked the fuel cap but it was okey too.
proclaimliberty2000 (3 месяца назад)
Mikael Sjödin at this point the best thing to do would be to try and drive the vehicle to an auto parts store to diagnose it with a computer scanner which they will do for free. This will help locate the problem.
Cowboys BBQ (4 месяца назад)
Amazing, can't wait to try this. Sharing on FB.
Josh Keller (4 месяца назад)
Hey there, i have 2001 4runner and after a few seconds after turning on the ABS,TRAC,VSC, and BRAKE light come on my dash and a loud beeeeeeep from under the dash. Has anybody have a clue whats going on? Also noticed that my anti brakes do not function while the beep is on.. the beep is intermitent.
qwandiddy (4 месяца назад)
Why was the ABS light flashing?
3d3dman (4 месяца назад)
I could not find any pin called TS only TC for a 2007 Camry. Are you sure it is not TC?
james trieu (4 месяца назад)
I am having a hard time with my 2009 Camry hybrid . is it the same if i have a push button start?
proclaimliberty2000 (4 месяца назад)
james trieu Take it to an auto parts store and they will check it for free with a diagnostic scanner to find trouble codes.
james trieu (4 месяца назад)
proclaimliberty2000 I did.... No luck
proclaimliberty2000 (4 месяца назад)
james trieu I don’t know the answer to that but I don’t think it could hurt trying part one through six.
Dhan Sayson (5 месяцев назад)
4&12?
juan Colon (5 месяцев назад)
Yes!!!! It worked😁😁, make sure you follow the directions carefully as this procedure took me a couple times to get right. I came back to this procedure after i tried all 6 of the procedures
JJ Flash (5 месяцев назад)
thanks
Yoga yon (6 месяцев назад)
I have 2004 highlander, got track off, vsc, and check engine light on at the same time, I tried video1-3, not working, but video 4 it worked? But come back few days later, I took it to the shop, they told me have to replace my oxygen sensor up and down. The code reader shoe c1223, c 1381, and p0128. What are those codes and should I have to replace the sensor? Thank you Paul.
Yoga yon (6 месяцев назад)
Thank you . Do you have any ideal about c1223 and c1381? Thank you
proclaimliberty2000 (6 месяцев назад)
None of those codes is for an oxygen sensor. A P0128 indicates a faulty thermostat or ECT (engine coolant temp sensor) which should be replaced first. Then reset the system by disconnecting the battery cables for 30 minutes, reattach and see what happens.
Iris Chen (6 месяцев назад)
Hi, I have 2004 highlander, and vsc, track off, and engine light coming out at the same time , I brought to the shop, they told me need to replace the oxygen sensor up and down. The code reader show p0128, c1223 and c1381. I tried the step 1-3 were not working, but the part 4 was work for while, later the 3 signal lights came out Again, what should I do now? Thank you
proclaimliberty2000 (6 месяцев назад)
I'm not sure how to advise you because the trouble codes you gave me have nothing to do with a bad oxygen sensor so I'm a little puzzled.
Too Old (6 месяцев назад)
This is above my pay grade
Hafiz ullah (6 месяцев назад)
sir please help me i havnt any scaner my vehical hilux intercooler shows problem ... by testing with test lamp the ecu give 23.24 code ...and serves icon and check light are shown in swich board
Oxford Minicbas (7 месяцев назад)
Hi Please help me ,, How can i reset (Check parking break system and check VSC system) My Vehicle is Toyota avansis 2011 D4D
Olja Coric (7 месяцев назад)
Does it work in toyota avensis diesel 2008 d4d?
Olja Coric (7 месяцев назад)
So I may try on my a car as well?
proclaimliberty2000 (7 месяцев назад)
It shouldn't make any difference that it's a diesel. You are blessed to have a diesel. Pretty much no diesel cars here in the United States which in my opinion is pretty stupid.
Wildo83 (7 месяцев назад)
Drove 350 miles to rescue my stranded wife with this! I hope God blesses you! In the mean time, can I send money somewhere? Saved our butts!
AWitty PIlot (7 месяцев назад)
How in the HELL did you find this!!!!  I don't see it in my Toyota service manual....    Well done!!!  I have an FJ that the lights just came on the other day.....Will be trying this Monday when I get home!!!  Thanks a TON!  God Bless you back!
Robert Stevens (6 месяцев назад)
AWitty PIlot ,
AWitty PIlot (7 месяцев назад)
Well I sure did! I watched them all.....great info.....thanks!
proclaimliberty2000 (7 месяцев назад)
I would suggest you start with Part 1.
Manuel Soto (8 месяцев назад)
Gracias por tu ayuda ..
big kev (8 месяцев назад)
tks
Sergio F. Lourido Urrutia (8 месяцев назад)
Hey... Does it work in a MY2007 Subaru Outback???
proclaimliberty2000 (8 месяцев назад)
It should.
Je' M (8 месяцев назад)
10x for this video. It worked
Valkyrie_117 (9 месяцев назад)
Beautiful! It worked on my 2006 Toyota 4Runner. Thanks!👍
Moondoggie5000 (1 месяц назад)
How did you find the correct ports on your 2006 4 runner ?
planestrainsandautomobile (8 месяцев назад)
smiley_face92 - oh hush Smiley. Yo cute self didn't fix that :-)
Jaijo Del (9 месяцев назад)
I did everything u explained and the light come right back on 4 seconds after I start car on.. now what's the problem??
Shane Tyler (9 месяцев назад)
Disconnect and reconnect positive battery cable it resets the computer
Cowboys BBQ (4 месяца назад)
Craig Anderson totally right
Craig Anderson (8 месяцев назад)
Shane Tyler that only resets it, it does not get rid of any issues you have. So the lights come right back on after you do that when the system recognizes the same issue you just reset. Also, it's hard on your computer to just keep dumping it like that all the time.
Justin Time (10 месяцев назад)
Only video i found to clearly and simply explain how to fix my problem, thank you!
Seth Hendrix (10 месяцев назад)
This is the only method that worked for me after watching several other videos. Thanks!
You say the CG and TS pinouts...do you mean the CG and TC pinouts? I can't find a TS pinout on my 2001 Sequoia... THANKS
proclaimliberty2000 (7 месяцев назад)
Feel free to put a scanner on and see what trouble code comes up. I had to purchased a 2 day subscription for $15 dollars at techinfo.toyota.com. to obtain the information I was looking for. Once I bought the subscription they helped me on the phone locate on the website the pinout information I needed. What your looking for is there. It's just using the right word searches.
proclaimliberty2000 (7 месяцев назад)
No. CG and TS is correct. You will have to purchase a 2 day subscription for $15 dollars at techinfo.toyota.com. Once I bought the subscription they helped me on the phone locate on the website the information I needed. What your looking for is there. It's just using the right word searches.
nugentj (7 месяцев назад)
Hello. Thanks for the videos. I have a 2005 4R SR5, and the VSC trac lights are on. Cant find the appropriate wiring diagram to tell me which terminals in the OBD pinout are CG and TS. Can you share a link to the diagram or anything? Not quite exactly sure where to get one. Could I resolve the lights issue with ScanGauge OBD II Scanner?
I did locate it. Thanks!
proclaimliberty2000 (10 месяцев назад)
No. I just checked the hard copy wiring diagram that I used when I did this and it's CG and TS.
boo! sboo (10 месяцев назад)
Your videos and the videos themselves are so clear to understand... and you are a class act! Thanks for sharing. Nobody else out there like you.
proclaimliberty2000 (10 месяцев назад)
Thank you for your kind words. It really means A LOT! God bless you and have a safe new year.
Suzanne Cox (10 месяцев назад)
Appreciate your good advice on this problem.....got through parts 1-3 without clearing the problem. Before my husband got to step 4, a friend told him to disconnect the positive battery connection, leave off for @ 5 minutes, reconnect it and start the car. Friend said that acts much like rebooting a computer. VIOLA! The lights cleared.
Jas Ortega (10 месяцев назад)
Paul.. please help I can't find any thing in my owners manual on the OBD..
proclaimliberty2000 (10 месяцев назад)
All I know is a lot of people have said the dealership wanted a fortune to fix this problem and this procedure has helped a lot of people. You could also put a computer scanner on the vehicle and see what trouble code comes up.
proclaimliberty2000 (10 месяцев назад)
Neither could I until I used techinfo.toyota.com
Jas Ortega (10 месяцев назад)
I tried the other steps and after doing both gas cap steps the two lights turned off for a few seconds the back on the OBD is the only one I haven't done
Jas Ortega (10 месяцев назад)
proclaimliberty2000 oh I see .. I just haven't been able to find anything 100% confirming the points ..
proclaimliberty2000 (10 месяцев назад)
Because it's a different model year there's no guarantee that the pin locations would be the same and you wouldn't want to short anything out and damage something.
Willie Wheeler (10 месяцев назад)
Worked for my 2006 Toyota Sienna. Thanks!
Jehanzeb Zia (11 месяцев назад)
My LC 202 a 2013 model has the same issue throwing trac off and check engine as well as the 4lo light flashing !!! Now i have takem it twice to the local toyota work shop and they scanned the problem and told me its a p0420 code which means according to them it needs change in cats and the whole exhaust system for the time twice they had reset it but after about 2 days they re surface ao now i help from you guys what should i do as it will cost me 4000 $ to get new exhaust system so any help info would be great at this time
Jehanzeb Zia (10 месяцев назад)
johnny Macon will go and have it checked thanks for the great advice but last thing can ut be the gaskit issue but my car temp gauge is totaly fine
johnny Macon (10 месяцев назад)
Pepe Vlogs they won't try replacement of the oxygen and exhaust temperature sensors first that will be the cheapest route get them OEM for your specific vehicle first and cheapest off EBay don't over pay I had the same symptoms on my Lexus 1995 Ls 400 model replacement of the sensors solved the problem eliminated 3 ob2 codes in the process got them off EBay for the Low Low !!!
johnny Macon (10 месяцев назад)
Pepe Vlogs don't believe the hype get a second and third opinions from a reputable mechanic shop that does honest work in town don't be ripped off !!!
johnny Macon (10 месяцев назад)
Pepe Vlogs don't do it your being Ripped off don't pay that kind of money for that simply go to a muffler shop or another mechanic and get their opinions second and Simply go on EBay.com and get your cat's and oem exhaust sensors for hell of a lot cheaper by more than a fraction than what that dealership will charge and let the muffler shop install them and keep your wallet much fatter because only fools go to dealerships!!!
Jehanzeb Zia (11 месяцев назад)
proclaimliberty2000 the dealership says its the cats now i am almost to the verge of pulling my hair out
RD Tech (11 месяцев назад)
Will this work in a 2003 Lexus gs300? My vsc and vsc off and check engine light is on
el Jefe (9 месяцев назад)
RD Tech get it scanned. It might be your oil control valves/solenoids.
Skyler Tegland (11 месяцев назад)
I went through these videos after the local shop handed us an estimate of $1412.59 to solve our indicator light issue. They hooked up their OBD and interpreted the results to mean that the catalytic converter was probably disintegrating, causing a temperature differential that was triggering the system warning lights. They wanted to replace the two sensors (oxygen and temp) and to replace the exhaust manifold as well (which integrates the cat. converter). I had my doubts, however, as the car had full power and normal engine temperature. I went through Paul's videos in order and solved the problem in about an hour. Thanks, Paul! You gotta love the age of information! After the reset, the car idle was rough for the first 25 miles as the computer idle compensation had to recalibrate. Now everything is perfect.
proclaimliberty2000 (11 месяцев назад)
That is fantastic! I'm so happy for you. You went the extra mile and it paid off BIG TIME! Thanks for letting me know. I really like to try and help people. Now you can go buy somemore Christmas presents. LOL! I can't even begin to imagine the amount of money that people pay out unnecessarily on auto repairs.
Ben Builder (11 месяцев назад)
It worked! Thanks Paul! 2011 Toyota Sienna SE 3.5L Only difference was that my OBD connection port was upside down from the one shown in the video. But it was shaped the same so the orientation was easy to discern.
Hayley White (11 месяцев назад)
I bought the Haynes Repair Manual for my 2005 Rav4. Nowhere does it give me the two ports to insert the two paperclips. Any ideas? Thank you!
proclaimliberty2000 (11 месяцев назад)
If you do not have a Toyota repair manual for your vehicle then the only other thing you can do that I know of ( which is what I did) is contact techinfo.toyota.com and purchase a 3 day subscription to their on line repair manuals. I think it was $19 dollars but well worth the money. It took some digging but I finally found the schematic for my vehicle with the help of their telephone tech support which comes with your subscription. Hope this helps.
ninongco (11 месяцев назад)
THANK YOU. This worked for a 2004 4Runner SR5
Archie Cendana (11 месяцев назад)
Hello sir. May i ask what would i do to fix my steering wheel i can't even move them right or left.
proclaimliberty2000 (11 месяцев назад)
Are you able to start the vehicle?
MrCooloo1 (11 месяцев назад)
Just wonderfull!! This tip worked perfectly for my Sienna 06 VSC's problem. Thank you!
Jakob Masat (11 месяцев назад)
Thank you very much, Paul. Worked great on my Landcruiser 90, 3.0 D-4D, 50th edition, 2001! Lights are cleared now!
chestyle usa (11 месяцев назад)
thank so much, thanks you !!!!
chestyle usa (11 месяцев назад)
perfect !!!
Sameer Khot (11 месяцев назад)
Oh my God...your video was a life saver. I only had to use your instructions from the first video and tighten the cap, indeed it was not all way tight before which explained the problem. Thanks so much for sharing this information. It saved me a bunch of money which Lexus would have happily ripped off to fix my IS250. Keep up the good work mate. Cheers. Sam
Racso RyM (11 месяцев назад)
Thanks solvers my vsc on my 2010 toyota Corolla, God Bless you Brother, Thanks.
syed abuthahir (1 год назад)
Do u have any idea about Suzuki swift duplicate key programming
Itsyaboi!!! (1 год назад)
Hi Paul, I'm good, I was able to fix my problem. Thanks again.
proclaimliberty2000 (1 год назад)
How did you fix it?
Itsyaboi!!! (1 год назад)
Morning Paul, Thank you so much for your help , I did replace the gas cap but now I have the VSC off light on and also the symbol four-wheel drive indicator light*2 (four-wheel drive models on. Please how do I remove that ? I read the manual and that means the four wheel drive is on. Thank you
Jimmy Cothran (1 год назад)
Worked perfectly on an 07 4Runner sr5 v6 4wd Thank you so much.
Tony Eze (2 месяца назад)
Hey Jimmy, did your ABS light come on along with the VSC lights? Just wondering if you cleared both with it because I have a 4 runner as well. Thanks
Jimmy Cothran (11 месяцев назад)
Vong Yang yes I believe it was the same I'll go double check. Yes it's the same.
Vong Yang (1 год назад)
Did you use the same ob connection terminals as shown in the video. I have an 07 toyota 4runner
rene amador (1 год назад)
is worked my friend i did the same like you did done tank you very much
ehassanz (1 год назад)
Worked on my 2009 Pontiac Vibe. Thanks!
George Yang (1 год назад)
Best instruction I finally got mine calibrated Thanks.
Dmitri (1 год назад)
Hey guys i had problem in 4 runner 2002.after i change HBB motor with pump. Brake started work perfect. Only one problem ligts is on and Firestone not can read ABS CODES. They say they not see ABS. And not possible to do zero point calibration My question. What can be wrong? Were is brain of ABS system? ABS module (come with master silinder) or ABS TRAC VSC COMPUTER CONTROL MODULE (what is left side of driver.) Thank you.
B (1 год назад)
For some odd reason my windows won't go down can you help me with that?
Jimmy Cothran (1 год назад)
B I think he explained that near the end of the video
Darayle Knause (1 год назад)
Worked on a 2004 Toyota 4Runner V8. Best video I could find on this topic. Thanks!
Bobby6180 (1 год назад)
Worked on my ‘05 Highlander this morning. Thanks!
Southern Texan (1 год назад)
Mine stay on!😡
Scizzor HonZ (1 год назад)
if you've performed parr 1,2,3,4 well ..... burn your car!!!🤔
Samson Okoro (6 месяцев назад)
hahahahaha damn funny as hell
proclaimliberty2000 (1 год назад)
That's pretty funny! Are you having some trouble?
Vanessa Perez (1 год назад)
All my lights are on but then my car began to shake and feel like my car wants to shut off. I am afraid too turn lights off and something be wrong with it
Abou Savané (5 месяцев назад)
Vanessa Perez salut.
Don Hyon (11 месяцев назад)
Vanessa Perez Was it your alternator?
umer pagara (1 год назад)
Vanessa Perez change your car ecu .
Максим Богданов (1 год назад)
Great! Thanks a Lot!
Rodney Mahabir (1 год назад)
Worked great for me. On my 2010 Corolla the cg & ts were the fourth terminals counting from the RIGHT. Fourth from the top and the bottom terminals. Thanks a lot!
بن زايد (1 год назад)
my car showed vsc sign ... i was doing 90mile and all over sundden I loat power the engine turned off ... and cutting gas ... whats the problem ?
Sae Kim (1 год назад)
L Medlock+ sounds like the fuel line needs replacement. Happened to my GS a few years back. Lexus covered it. Have them check your fuel lines...not the pump but the lines
Lashay Medlock (1 год назад)
Iam Tariq my Lexus did the same. It had to be towed to the shop. The shop initially said it was the fuel pump. They charged me $411, still didn't work. They then said it was the main fuse another $100, still nothing. They then said they would see if it was the GPS tracker the car lot put on there, still nothing. I don't have the kind of money they are trying to ask me for. I'm lost, I just paid my car note do I can't afford a rental. The car lot sent me to this shop because it is the one they use. I've only had this car for about 4 1/2 months. Is there anything else that could be wrong besides what you stated in all 4 videos and what the shop has already tried. Mine shut off no warning then the vsc, Trac, engine light came on. It starts and shuts immediately off. It's been at the shop since Friday 😔😔😭
proclaimliberty2000 (1 год назад)
You first need to have a computer scanner diagnosis done.
ir ax (1 год назад)
could you please help identify the CG/TS ports? cannot find any info. trying to fix Toyota Sequoia 08 great videos! thank you!
proclaimliberty2000 (1 год назад)
You will have to purchase a 2 day subscription for $15 dollars at techinfo.toyota.com. Once I bought the subscription they helped me on the phone locate on the website the information I needed. What your looking for is there. It's just using the right word searches.
Nick Candu (1 год назад)
Thanks a lot this method has help me solve Check VSC system.
Geshom Lupenga (1 год назад)
I tried it on toyota mark x, couldn't work. Any other methods please?
Saint Preferred (1 год назад)
Good post!! Smart guy, good video.
NewsFunPolitics (1 год назад)
Nice video..i like it.
Clara Martinez (1 год назад)
Excelent video and easy process but I have a 2007 Toyota Camry Hybrid and works perfect for 3-5 minutes. after that the lights come again. I try tree times. same result. It is possible any aditional step for Hybrids?
proclaimliberty2000 (1 год назад)
Make sure you watch and perform Part 1, 2 & 3. Also inspect all vacuum hoses for proper connection and or kinks. If that doesn't fix the problem, you will need to have the car diagnosed with a computer scanner.
yasser al yasser Alyasser (1 год назад)
Lexus LS 430 Thank you
Davidian Bros Productions (1 год назад)
Is this a Rav4? I have a 2005 Rav4with the same problem?
JoAnn Coleman (1 год назад)
Paul Thank you, I was able to fix my VSC light on my Lexus, with part one of your video. Its crazy how many times I took it to get it diagnosed and the VSC light kept coming back. Hopefully its fix for good now. Now I am going to reset my windows because I cannot control my back windows. Thank you and please keep posting.
Dana Johnson (1 год назад)
my 2002 toyota 4runner makes a loud beeping sound with no lights on and when the car is not running. and keys are not in the ignition. Please help if you can.
FamiliaC (1 год назад)
Amazing! Information is power! Thank you!
cius esnal (1 год назад)
i like it.

Хотите оставить комментарий?

Присоединитесь к YouTube, или войдите, если вы уже зарегистрированы.