На главнуюХобби и стильПохожее видеоЕще от: PowerModz

Land cruiser 1HZ 1HDT 1PZ Valve shim adjustment tutorial

Оценок: 364 | Просмотров: 141345
A "how to" on how to adjust the valve shims on your toyota land cruiser with 1HZ and 1HDT engine, but will work on other as well.
Категория: Хобби и стиль
Html code for embedding videos on your blog
Текстовые комментарии (51)
YouTuber 12345 youtuber (2 месяца назад)
Your are awesome.
vaz25 (5 месяцев назад)
Thank you very much, благодарю, все понятно, с почтением )
Karl Magnússon (1 год назад)
Skipta um heddpatningu í land rúsínur 90 ,1997
chris arundel (1 год назад)
Best and easiest way is to set engine at BOTTOM DEAD CENTRE with timing belt cover removed, once crank is at bottom dead centre, remove timing belt and check the valve clearances while turning the camshaft through a full rotation, once you have written down all clearances, pull cam out and set up each valve to correct shim hight, re install cam, turn cam to double check clearances, if ok turn back to bottom dead centre mark, re-install timing belt, and put engine back together. The reason for setting at bottom dead centre is because all 6 pistons (or 5 in 1pz) will be far enough down the bores so valves cannot contact the pistons. This is how it states to set clearances in the Toyota factory workshop manual
Ivan Bremer (5 месяцев назад)
DO NOT DO THIS. The 1hz is a contact motor. If you turn the cam without the bottom end, ie No timing belt, The valves WILL impact the piston. It states this in the work shop manual. Please, You don't have to believe me, seek your own advise/manual.
Nick's DIY (1 год назад)
Nice shim compressing tool, do you have an amazon link for that?
John R (2 года назад)
Thanks for the tutorial. Your calculation 2.93 + (0.3 - 0.4) = 2.83. I went to back your previous clearances measurements and there is no 0.3? Unless you using 1 valve which wasn't shown previously?
Xoliul (2 года назад)
I was really hoping you wouldn't be using the mythicaly, expensive Toyota SST... Kind of voids the whole tutorial thing, it's pretty easy when you have that!
Ernest Kerich (3 года назад)
The tutorial is teriffic! I wonder where can one find the valve adjustment tool? I am from Nairobi, Kenya. I have looked around but am unable to get it even online. Any idea? Kerich.
khelif benha (3 года назад)
god job sr
Gary drivinit (3 года назад)
Great Tutorial can you tell me if the sst number is the shim set part number cheers
mark yorong (3 года назад)
how to set timing distributor on the on toyota land crouser
Che Myers (4 года назад)
can u do a video explaining the Valves adjustment with a FJ 60? it´ll be really cool!
Jake Curl (4 года назад)
Really excellent video - well produced.
TheGervarod (5 лет назад)
hi there just wondering are the 70/75 series LC 6 or 4 cylinders Cheers
Girum y (5 лет назад)
Thanks for the video. Does anybody know Where I can buy the tool- Toyota sst 09248-64011 from?
PowerModz (5 лет назад)
If the intake valve shims are the wrong size (too big) they can give you a knocking sound - it is basically exhaust coming back out the intake valve - dont run like that for long. the intake manifold will feel hot just after start up - not from normal engine heat - but from exhaust gas.
martin jones (5 лет назад)
i have a 1hz and it has a problem i have put a new head on it and since it has been running it has had a big nocking nosie coming from the rocker cover now would that been caused by the vavle shims or something else
PowerModz (5 лет назад)
no problem thanks for watching!
Riaan Van der Walt (5 лет назад)
o, ok, thanks :)
PowerModz (5 лет назад)
I'm pretty sure you just adjust the valves with a set nut on that one.
Riaan Van der Walt (5 лет назад)
Hi Louis. I have the 2H engine, i believe it's a OHV motor, working with pushrods. Do i need to do this shim replacement for it too?
KNIGHT (5 лет назад)
Thank you very much for communicating so far.....Good luck.!!!
PowerModz (5 лет назад)
yes 12 V, biggest battery I can fit, same size.
KNIGHT (5 лет назад)
Thx for the advise....your one also a 12v version? Are you using same size batteries or one big (90am/h) and one small (70am/h) batteries?
PowerModz (5 лет назад)
ah ok that is easy - the left side, one in front of the other, I did the same thing, made my own large tray and they fit perfectly.
KNIGHT (5 лет назад)
Is that so....then if I wanted to put double batteries for a single battery version (12v) Land Cruiser HZJ 79; What is the best place to install the secondary battery? Is it the right side of the engine bay or the left side of the engine bay behind the factory fitted battery? What will be the practical place of a RHD cruiser? Pls. advise me!
PowerModz (5 лет назад)
its so hard to say, they have many specs for many countries.
KNIGHT (5 лет назад)
It is made in Japan and made for Asian market. I think they are sending the dubai spec here. I'm from Sri Lanka.
PowerModz (5 лет назад)
What country did the truck come from? There are many variables depending where the truck comes from - it could have 2 batteries, 1 batt, or 12/24 v.
KNIGHT (5 лет назад)
Thanks a lot for your quick reply.. I'm asking about a RHD vehicle. If it is a 12v do they have two batteries instead of one? if so what will be the placement? thx Sorry for disturbing!
PowerModz (5 лет назад)
it depends on where the vehicle is sold, there are three possible locations, there are 3 locations listed in the EPC, two on the left side and one on the right. So it all depends on whether your truck is left and or right hand drive. If 12V it can have one battery on the front position left handside, if 24V (If still made) it can have 2 on the left in LHD vehicles. I will see what my electronic parts manual says - but I have to try to find it:)
KNIGHT (5 лет назад)
In 2012 Land cruiser HZJ 79; what is the battery placement? (2battery models) one in left side of the engine bay and other one in right? or both are in left side of the engine bay? Are they 12V or 24V? Pls. help!!!
PowerModz (6 лет назад)
Thanks for watching!
Akadectra (6 лет назад)
Excellent video. Thank you very much!!
PowerModz (6 лет назад)
Some make their own tool - but it's tricky.
dave hall (6 лет назад)
i don't have that tool to compress.
PowerModz (6 лет назад)
Thanks for your support!!
mel (6 лет назад)
excellent video. Best landcruiser tutorials on youtube.
PowerModz (6 лет назад)
@lexusfan100 It would sound like a diesel truck, the 1hz sounds smooth when running right - kinda like a car engine.
lexusfan100 (6 лет назад)
nice..do u know what the sound the engine would make while driving if the shims are not adjusted properly..thanks
PowerModz (6 лет назад)
@ChuckmeisterC just the pick up!
ChuckmeisterC (6 лет назад)
My '98 1HZ needs a bit of this love. Thanks for uploading. What LC are you onto now?
PowerModz (6 лет назад)
@MonkeySpecs301 i have some , what size do you need?
MonkeySpecs301 (6 лет назад)
Hey mate, i'm in the US you know where i can find 1hz shims?
Ramdy Guerrero (6 лет назад)
magnifico video
Garry Scaife (6 лет назад)
well done ...... :))
PowerModz (7 лет назад)
@dRMaBUseXIV Thanks Mate!
PowerModz (7 лет назад)
@bdmdos You can get one form toyota easily!
MatthewJohn Gill (7 лет назад)
top job, wd.
PowerModz (7 лет назад)
@kabodkhwaamkhid Thanks!

Хотите оставить комментарий?

Присоединитесь к YouTube, или войдите, если вы уже зарегистрированы.